Archive for 2007

meshy presentation December 19th events - December 15th, 2007 - Marloes de Valk - No Comments

This Wednesday, December 19th, we’re presenting the work and research we did this fall during our residency at Waag Society on the meshy project. If you can’t make it there is a stream produced by KillerTV, and if you can make it, there are some drinks ;) Date: 19 December 2007, 8 pm. Location: Theatrum […]

read full post...

semi-rigid urethane even better? input - December 15th, 2007 - Marloes de Valk - No Comments

My little epoxy shop was finally up and running, working like a charm and heading for great success until… well until I ran out of epoxy and went to the shop to find out they DIDN’T ORDER ANY NEW AAAAAAAAAAAAAAAAAAAAH!!! I only produced 1/3 of the total needed amount so had no choice but to […]

read full post...

meshy factory hardware - December 10th, 2007 - aymeric - 1 Comment »

All the nodes are now complete! Last batch was done 4 at a time in a brainless repeat mode enjoying the fume from the melting lead…

read full post...

epoxy works better input - November 30th, 2007 - Marloes de Valk - No Comments

After the first disastrous attempt at making a cast, I switched from silicone to epoxy. Epoxy becomes solid very gradually so I would have time to wait until it was semi-solid, then paste it into the mold, push the 2 parts together and let it dry. This way I would not have to pour anything […]

read full post...

meshy assembly input - November 29th, 2007 - Marloes de Valk - No Comments

Another mass soldering post, this one less skeptical since the procedure has been drastically optimized and this time 4 beautiful boards saw the light! Once again in the midst of a whirlwind of chaos but resulting in a little garden with 4 shiny noise emitting flowers.

read full post...

meshy mass soldering input - November 29th, 2007 - Marloes de Valk - No Comments

Today we did a session of meshy mass soldering. The hardware design is final and the honorable job of reproducing it at least 8 times has commenced. Optimized approach will render about 2 boards in one session (the session length is still under debate and so is the optimized approach). This part of the project […]

read full post...

failed first experiment input - November 28th, 2007 - Marloes de Valk - No Comments

Today I finished the hollow part of the mold. I spent most of the day smoothing both parts of the mold with sandpaper and getting rid of some of the errors the CNC made. Some edges are simply not possible for the machine to make, so I have to manually adjust. It is turning out […]

read full post...

CNC milling pr0n input - November 27th, 2007 - Marloes de Valk - 2 Comments »

It is hard to stop watching the machine while it slowly frees your design from a heavy block of chemical wood. Some CNC milling pr0n:

read full post...

meshy artist in residence input - November 26th, 2007 - Marloes de Valk - No Comments

It is the 26th of November today, and we are in the 9th week of our artist in residence at the Waag Society. The project is progressing a lot and we are now starting to work on the networking and data exchange part of the project. We are simultaneously working on the cases for the […]

read full post...

milling a mold for meshy input - November 22nd, 2007 - Marloes de Valk - No Comments

Today we started making part 1 of the mold, to cast a case for the Meshy objects. We are using a CNC (Computer Numerical Control) milling machine (BZT pf 1000 c) at the Waag Society to mill out the shape. The machine is amazing, I can’t stop watching it. The material used to mill out […]

read full post...